The Paveosub-115sp is a very compact self-powered bass reflex subwoofer with 3-channel 4 kW power amplifier module and DSP speaker management system.
With its low profile of only 36 cm and a width and depth of only 54 x 57 cm, the bass is ideal for fixed installations where a discreet appearance is required and the loudspeakers need to be integrated into the architecture as unobtrusively as possible.
In mobile use, the Paveosub-115sp saves a lot of space and weight with a transport volume of only 110 litres. The two large handles can take hold from all sides and are located at the centre of gravity.
A removable and stackable front wheel board is available as an accessory for easy handling of the subwoofer. The optional transport protective cover also can be used as weather protection at outdoor events.
The Paveosub-115sp is equipped with a newly developed neodymium transducer with 4″ voice coil that can handle 1.000 W AES. The magnet system has three demodulation rings for particularly low distortion. Massive cooling fins ensure low power compression at maximum performance. Together with a high linear excursion and a low moving mass, the subwoofer offers deep, powerful and at the same time very precise bass reproduction.
Internal bracing ensures maximum stability and prevents unwanted cabinet resonances.
The subwoofer can be used flat or upright. On two sides there are stacking moulds, rubber feet and M20 flanges for flexible use with an attractive appearance, depending on the combined satellite loudspeakers. Standing upright, the Paveosub forms a very slim silhouette.
The stacking moulds on the top of the sub are in the same foodprint as the CXN-16 stage monitor. In addition, both loudspeakers have a width of 54 cm and thus form an elegant optical unit and are a professional set for drum or DJ monitoring, for example. A self-powered Paveosub-115sp can power a CXN-16 bi-amping in half-powered mode.
The active electronics are convection cooled by a large heatsink and are maintenance free. No dust or moisture can be sucked or drawn in, making the Paveosub-115sp ideal for permanent installations. The robust cooling fins are amply rounded and have no sharp edges.
The control unit, DSP unit, signal connections and the Speakon OUT terminal are protected against moisture with a weather-proof, transparent cover. The cooling system is waterproof and the powerCON TRUE1 connectors are equipped with a rubber sealing cap.
Features of the integrated Class-D amplifier unit:
- 3CH: 1 x 2.400 W + 2 x 800 W on 4 Ω
- Maintenance-free electronics
- Input Limiter and Peak Limiter
- Switch on power rush protection
- Protection circuit for On/Off switch transients
- Smart Fuse protection
- Under and Over voltage protection
- DC protection of outputs
- Temperature monitoring of the heatsink and transistors
- Enclosed cooling system, no air is drawn into the interior
- High damping factor > 1000 (8 Ω, 1 kHz)
- Low THD, THD + N < 0.05 % (20 — 20,000 Hz, 8 Ω)
Features of the built-in DSP loudspeaker management system:
- High quality DSP board with best audio characteristics
- USB and Ethernet interface (with optional built-in wireless W-Lan module)
- Direct manual speaker operation via Display button and control wheel
- 4 language menu selections for Manual
- 80 presets internally stored and recalled. Unlimited on PC
- Real-time access to meter bridge on PC via VA-W LAN remote software compatible with HDSP amplifier serie
- Simple menu
- 96 kHz sampling rate
- 120 dB dynamic range
- 20 parametric EQs per way
- Flexible routing
- X-over
- Limiter
- Short delay for time alignment of the chassis
- Long delay for delay lines up to 270 m
- Phase
- Firmware upgradeable via interface
Control
The woofer is in 8 Ω.
The 15″chassis of the Paveosub-115sp is powered by one channel (1.580 W/8 Ω) of the internal power amplifier module. 2 x 800 W/4 Ω are available for satellite or monitors.
A Paveosub-115sp can power a second Paveosub-115 and power up to 4 additional speakers.
